• Hotline
  • 0916 557 639
Hỗ trợ trực tuyến
  • han@vietphat.com
    0938 927 339
  • hon@vietphat.com
    0916 557 639
  • kiet@vietphat.com
    0901 622 187

SERIES 2000

  • 0%
  • Mã sản phẩm:
  • Kho hàng: Còn hàng
  • Tình trạng: Mới
  • Nhà sản xuất: Dwyer
  • Xuất xứ: Mỹ
  • Thông tin bảo hành: 12 tháng
  • Giá thị trường : Liên hệ
  • Giá bán: 0 VNĐ
  • Hãy gọi ngay vào Hotline để được tư vấn trực tiếp về sản phẩm
  • Nhập số lượng
  • + -
 
 
 Series 2000
Magnehelic® Differential Pressure Gage
Indicate Positive, Negative or Differential, Accurate within 2%


Select the Magnehelic® gage for high accuracy--guaranteed within 2% of full scale--and for the wide choice of 81 models available to suit your needs precisely. Using Dwyer's simple, frictionless Magnehelic® gage movement, it quickly indicates low air or non-corrosive gas pressures--either positive, negative (vacuum) or differential. The design resists shock, vibration and over-pressures. No manometer fluid to evaporate, freeze or cause toxic or leveling problems. It's inexpensive, too. 
The Magnehelic® gage is the industry standard to measure fan and blower pressures, filter resistance, air velocity, furnace draft, pressure drop across orifice plates, liquid levels with bubbler systems and pressures in fluid amplifier or fluidic systems. It also checks gas-air ratio controls and automatic valves, and monitors blood and respiratory pressures in medical care equipment. 
Note: May be used with Hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi. 

Service: Air and non-combustible, compatible gases. (Natural Gas option available.) 

Application:
  • Filter Monitoring
  • Air Velocity with Dwyer Pitot Tube
  • Blower Vacuum Monitoring
  • Fan Pressure Indication
  • Duct, Room or Building Pressures
  • Clean Room Positive Pressure Indication

Specification:
  • Wetted Materials: Consult factory.
  • Housing: Die cast aluminum case and bezel, with acrylic cover, Exterior finish is coated gray to withstand 168 hour salt spray corrosion test.
  • Accuracy: ±2% of full scale (±3% on -0, -100PA, -125PA, -10MM and ±4% on -00, -60PA, -6MM ranges), throughout range at 70°F (21.1°C).
  • Pressure Limits: -20" Hg. to 15 psig.† (-0.677 bar to 1.034 bar); MP option; 35 psig (2.41 bar), HP option; 80 psig (5.52 bar).
  • Overpressure: Relief plug opens at approximately 25 psig (1.72 bar), standard gages only. See Overpressure Protection note on Catalog page.
  • Temperature Limits: 20 to 140°F.* (-6.67 to 60°C).
  • Mounting Orientation: Diaphragm in vertical position. Consult factory for other position orientations.
  • Process Connections: 1/8" female NPT duplicate high and low pressure taps - one pair side and one pair back.
  • Weight: 1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g).
  • Standard Accessories: Two 1/8" NPT plugs for duplicate pressure taps, two 1/8" pipe thread to rubber tubing adapters and three flush mounting adapterswith screws. (Mounting and snap ring retainer substituted for 3 adapters in MP & HP gage accessories.)
* For applications with high cycle rate within gage total pressure rating, next higher rating is recommended. See Options Page. 
* Low temperature models available as special option.
Danh sách bình luận
Gửi bình luận
/5 điểm
/5 điểm

Sản phẩm khác